Guide for the Restoration of Buildings After Floods

 

1.1.
ZA ZIDOVE OD ČVRSTIH MATERIJALA (OPEKA, BLOK, GAS-BETON...):

• Remove any remaining water from the premises. • Before drying, clean all contaminated surfaces and remove any dirt. • Check the condition of walls, ceilings, and all surfaces that have been exposed to water. After evaluation, remove all fragile and weak surfaces to allow proper drying of the areas that need restoration. • DRYING THE BUILDING is necessary before any work can begin. After drying the water from the walls and floors, mold may appear, which can be treated with the biocidal agent BK-SaniCid, specifically designed for the effective removal of a wide range of wall algae and mold.

1.1.1.
Ukoliko je došlo do oštećenja u sloju maltera:

1. Check the moisture level in the wall using a moisture meter to ensure that the building is properly dried. 2. Remove all fragile and poorly bonded plaster surfaces. The surface must be load-bearing, solid, dust-free, dry, and free from any remaining weak layers. 3. Apply the primer BK-Penetrat to such surfaces; for concrete surfaces, it is necessary to apply the structural primer BK-Beton Kontakt. 4. The prepared surface can then be restored using BK-Mal 420 plaster. Once the plaster is dry, apply the primer BK-Ultra Prime and then proceed with the smoothing of the surface. 5. Where necessary, level out the areas with leveling compound. Recommended products for leveling compounds are: BK-Gletex Acryl, BK-Gletex Nivelex, and BK-Gletex Universal. 6. After sanding the leveled surfaces, it is necessary to apply BK-Primer, which is intended to improve adhesion, uniformity, and reinforcement of the substrate before applying interior paints. 7. Once the surface is prepared, you can apply dispersion paints. Recommended paints are: BK-Crystal, BK-Gold, BK-Pol, BK-Pol Protect, BK-Delux.

1.1.2.
Ukoliko je došlo do promena na završnom sloju zida (flekavost, šarenilo, bubrenje, oštećenja boje na zidu)

1. Check the moisture level in the wall using a moisture meter to ensure that the building is completely dry. 2. Remove all fragile and poorly bonded surfaces. 3. Treat the walls with the concentrated biocidal agent BK-SaniCid, which is used for the effective removal of a wide range of wall algae and mold. 4. Apply a deep-penetrating primer for poorly bonded surfaces, BK-Penetrat, to all areas. 5. Perform smoothing and painting according to the instructions described for plaster damage repair (points 5 to 7).

1.2.
REŠENJA ZA SANACIJU ZIDOVA OD GIPS-KARTON PLOČA

1. Remove all gypsum boards that have been in contact with water. Install new gypsum boards on the existing framework. 2. If adhesive bonding of gypsum boards is required, use BK-PlasterFix. 3. Fill the joints between the gypsum boards with BK-Fil. Apply the primer BK-Ultra Prime. 4. Perform smoothing and painting according to the instructions described for plaster damage repair (points 5 to 7).

• Remove any tiles and floor coverings that are detaching from the walls and floors to allow the surfaces that need restoration to dry. • Check the moisture level in the wall and floor using a moisture meter to ensure that the building is completely dry.

2.1.
U SLUČAJU DA JE POTREBNO ODSTRANITI PLOČICE

1. After removing the tiles, remove any remaining adhesive and prepare and level the surface for laying new tiles. 2. In the case of uneven floor surfaces, level the substrate with a self-leveling compound such as BK-Liv 10 or BK-Liv 30. 3. After surface preparation, apply the primer BK-Ultra Prime. 4. Coat the surface with the waterproofing coating BK-HidroStop 2 or BK-HidroStop Extra. 5. Depending on the requirements, choose the appropriate adhesive for ceramic tiles. Recommended products: SiproFix BK 160 SuperFlex, SiproFix BK 160 White, SiproFix BK 170 Elastic, SiproFix BK 110 Flex. 6. Clean and dust the joints between the tiles and fill them with the grout BK-Fugomal.

2.2.
UKOLIKO SU PLOČICE OSTALE ČVRSTO ZALEPLJENE, NAKON ČIŠĆENJA POVRŠINE MOŽETE SAMO ZAMENITI FUG MASU:

1. Remove the existing grout using a grout removal tool. 2. Clean and dust the joints between the tiles, then fill them with the grout BK-Fugomal.

2.3.
UKOLIKO SU PLOČICE OSTALE ČVRSTE I ŽELITE DA ZALEPITE NOVE PLOČICE PREKO POSTOJEĆIH:

1.
Očistiti, otprašiti, odmastiti celokupnu površinu postojećih pločica i naneti podlogu BK-Bond.
2.
U zavisnosti od zahteva odabrati odgovarajući lepak za keramičke pločice.
Preporuka: SiproFix BK 160 SuperFlex, SiproFix BK 160 White, SiproFix BK 170 Elastic.
3.
Fuge između pločica očistiti, otprašiti i ispuniti masom za fugovanje BK-Fugomal.

2.4.
U SLUČAJU DA SU PODNE PODLOGE SVE VRSTE PARKETA, LAMINAT I DAŠČASTI PODOVI:

1. After removing all floor coverings, proceed to remove any remaining adhesive, prepare, and level the surface for installing new floor coverings. 2. Depending on the irregularities of the floor surface, level the substrate with a self-leveling compound such as BK-Liv 10 or BK-Liv 30. 3. Check the moisture level of the surface before applying the primer. 4. After surface preparation, apply the primer BK-Parket Fix PU Prime to the leveled surface. 5. Use a two-component adhesive to install the floor coverings. • After the water recedes, the external wall surfaces should be cleaned either manually or with a machine.
• Before any work, it is necessary to DRY THE BUILDING. After washing and complete drying, treat the façade surface with the biocidal agent BK-SaniCid according to the instructions.
• Pay special attention to façade surfaces with thermal insulation to ensure they are solid and well-dried before cleaning the surface with the biocidal agent.

3.1.
Ukoliko nije došlo do mehaničkog oštećenja fasadne površine:

1.
Za mineralne fasadne površine naneti pologu BK-Penetrat a za sve ostale fasadne površine naneti podlogu BK-Ultra Prime ili BK-Grund Universal.
2.
Fasadnu površinu prebojiti u dva sloja akrilnom fasadnom bojom BK-Fas Acryl ili silikonskom fasadnom bojom BK-Fas Silicon.

3.2.
Ukoliko je došlo do mehaničkog oštećenja fasadne površine neophodno je utvrditi stepen oštećenja kako bi se dalo adekvatno rešenje za sanaciju objekta.

For any additional questions, you can contact us via email at: [email protected]. You can download the guide HERE.

 

Bekame

What are the advantages of installing a quality facade?

Facades: Savings with the help of high-quality facade systems

What would the savings on heating and cooling costs of up to 40% mean for your home budget? From month to month, the lack of a quality facade is the main cause of high costs for heating and cooling. According to the report of the Energy Agency of the Republic of Serbia, owners of family houses spend the amount in the range from 543 EUR to 975 EUR per year for heating residential space of 100 m2. In average, that’s approximately 759 EUR per heating season or as much as 18.977 EUR for a period of 25 years. When cooling costs are added, the figures are even higher.
The data of the Ministry of Mining and Energy draw attention to the fact that more than 70% of houses in Serbia does not have high-quality, and most often any thermal insulation of the facade. Due to poor quality facade systems even 40% of energy for heating and cooling is wasted. It’s an approximate loss of 126 EUR per household per year, and Serbia has 2,487,880 households. When the thermal insulation is not of good quality, money “leaks through the walls”.

Safety outside, warmth inside

In order to avoid unpleasant experiences and situations, it is necessary to keep in mind that poor installation of the facade can produce numerous problems. Improperly installed or poor-quality thermal insulation facade system can cause further damage to the owner of the building and produce insufficient cost savings in relation to the investment – which is a double loss. In the case of a poor-quality facade, problems such as unstable temperature and humidity in the house, condensation on the walls, mold in the corners, the appearance of cold bridges or a damaged appearance will not be solved. Improperly installed thermal insulation facade system can hardly be repaired locally. In most cases, the complete installation must be completely repeated. Inadequate thermal insulation, without certified materials, is not subject to warranty, which excludes possible support from the manufacturer in the technical sense, as well as troubleshooting. So, a bad and incorrectly installed facade system can bring you more harm than good. Therefore, for a pleasant stay in your house, quality thermal insulation is of the utmost importance. A well-insulated house is warm in winter, and protected from overheating in summer. No condensation and mold, and the manufacturer’s warranty lasts up to 25 years.

AII in one

A quality thermal insulation facade system saves you money and reduces bills by 10 to 40% per month. With it, the lifespan of your house becomes significantly longer, and the value of the property increases. The certified façade system is subject to the manufacturer’s guarantee, and a positive impact on the environment should be taken into account. First of all, the main advantage of quality facade systems lies in the fact that it is a solution without disadvantages. If you own a family home, why waste your money unnecessarily if you don’t have to? You will install the Bekatherm thermal insulation facade system once, and it will work for you in the long run to save on heating and cooling costs. The absence of facade thermal insulation leads to unnecessary energy consumption and contributes to air pollution that we breathe every day. CO2 emissions are increasing, as is the consumption of limited natural resources. So, high-quality thermal insulation also brings the positive impact on the environment.

  THE QUESTION THAT COMES FROM ALL OF THIS IS WHAT IS A QUALITY FACADE SYSTEM? WHY IS IT SO IMPORTANT? WHAT ARE ITS MAIN CHARACTERISTICS AND ADVANTAGES?

 

A quality facade system is, above all, a system of a reputable manufacturer that meets all the requirements prescribed by the Rulebook on Energy Efficiency of Buildings . As a regional leader in the production of finishing construction materials, Bekament offers several facade systems with advanced thermal insulation characteristics. As such, these façade systems can successfully meet all regulatory, user and market requirements. This is confirmed by the numerous certificates that the company has, as well as thousands of satisfied customers in over 10 EU countries and the region. In addition, training and coaching are the foundation of the company’s decades-long success. In the Bekament training center, over 2,000 facades installers and other contractors acquire professional training and education in the field of finishing construction works every year. In addition to certified products, Bekament company also provides professional technical support when choosing materials. The effect of real materials Each system represents much more than a simple sum of parts. Small things make big differences. That is why Bekatherm thermal insulation facade systems consist of mutually harmonized materials of the highest quality. In addition to the insulation boards, the façade system also consists of mineral adhesive, glass mesh for reinforcement, corner moldings, primer and final façade render.
We offer four Bekatherm facade systems: Bekatherm Standard White is the best-selling facade system and includes the most cost-effective solution for thermal insulation of facades. It is suitable for all types of substrates. It can be used for all new and old buildings. The basis of this system is an insulated board made of expanded polystyrene EPS – styrofoam. Properly installed thermal insulation facade system is characterized by resistance to UV radiation and atmospheric influences, quick and easy installation as well as exceptional workability of the material, and the finishing facade render offers a wide range of shades. All components of the Bekatherm Standard White facade system are ETA certified with a guarantee of up to 25 years.
Bekament Standard Graphite facade system has 20% higher thermal insulation properties compared to thermal insulation with white styrofoam insulation boards. The basis of this system is a graphite styrofoam insulation board. Properly installed thermal insulation facade system is characterized by excellent water repellency, exceptional workability and easy installation of materials. All components of the Bekatherm Standard Graphite facade system are ETA certified with a guarantee of up to 25 years. Bekatherm Prestige is a high-quality facade system. The basis of this system is an insulating board or lamella of mineral (stone) wool. It is characterized by A2 class of incombustibility, excellent vapor permeability and sound insulation. All components of the Bekatherm Prestige facade system are ETA certified with a guarantee of up to 25 years.. Bekatherm Plus is a system characterized by exceptional water repellency, resistance to mechanical shocks, as well as UV radiation and atmospheric influences. In family houses, it is most often used to make plinths. The basis of this system is an insulating board made of extruded polystyrene (high-density styrofoam). You can get acquainted with the importance of proper installation of thermal insulation facade systems through educational and meaningful video material (tutorial) which clearly, precisely and concretely explains this process. Want to find out more? For additional information regarding facade systems, prices and installation methods, call Bekament professional technical support team 034 677 75 00. We invite you to share on our pages on social networks, Facebook / Instagram, what, in your opinion, are the advantages of a quality facade? Do you like the text? Share it with your friends.

What are the advantages of a system solution for waterproofing and laying ceramics in the bathroom?

The bathroom is one of the most important rooms in a house or apartment, but it is also the most sensitive part of the interior due to the daily presence of water and moisture from its intensive use. That is why special attention is given to equipping the bathroom. To meet all aesthetic and functional requirements, particular care must be taken in choosing quality materials to ensure that waterproofing and ceramic tile installation, as well as their proper installation, are effective. For long-lasting bathroom protection, professional contractors recommend the use of system solutions. What are system solutions for the bathroom, and what are their benefits? We will demonstrate this with the HYDRO CERAMIC BATHROOM system for waterproofing and ceramic tile installation in the bathroom. This system represents a reliable, high-quality, and cost-effective solution that provides secure and long-lasting protection against water and moisture penetration. It is characterized by excellent waterproofing, resistance to mold formation, and a good price-to-quality ratio. It is easy and simple to install and is also suitable for underfloor heating. To achieve these advantages, the proper installation of this system involves the use of seven different materials, each with a precisely defined place and role within the system. These are: 1) primer, 2) self-leveling compound, 3) waterproofing coating, 4) waterproofing tapes, 5) adhesive for ceramic tiles, 6) grout, and 7) sealants.

The proper installation process of the HYDRO CERAMIC BATHROOM system

Before installing the given system solution, it is necessary to complete the works on the plumbing and sewage systems, as well as the electrical, ventilation, and heating installations, and to install the exterior and interior joinery. Since there is no perfectly even surface for finishing works, the uneven substrate needs to be prepared. First, the surface should be dusted, and then primed. For priming, we use BK-Ultra Prime universal primer. This layer improves adhesion, equalizes absorption, and binds dust particles. To achieve a sufficiently smooth surface without sharp edges and damage, it is necessary to fill in irregularities in the horizontal floor surface. For this purpose, we recommend the self-leveling compound BK-Liv 10. This compound is used for thin-layer leveling of concrete surfaces and cement screeds before applying waterproofing. After drying, this surface and the walls need to be primed with BK-Ultra Prime universal primer.

Waterproofing Installation

Once the substrate drying period is complete, a waterproofing coating is applied. The HYDRO CERAMIC BATHROOM system includes BK-HidroStop 2, a two-component, flexible polymer-cement waterproofing coating for horizontal and vertical surface protection against moisture. The first step in using the waterproofing coating in the HYDRO CERAMIC BATHROOM system involves applying it along the joints of contact surfaces. In the first layer of BK-HidroStop 2, applied to the corners and at the joint between the floor and wall, the BK Tape – an elastic waterproofing tape – is embedded. Then, a second layer of waterproofing coating is applied along the length of the tape. The waterproofing coating is applied to the remaining surface of the walls and floor, connecting the areas where the waterproofing tapes are located. After 12 hours of drying of the first layer, but while the first coat is still slightly damp, the second layer is applied. The second coat is applied crosswise, at a 90-degree angle to the direction of the first layer. The total thickness of the application should be around 2 mm.

Ceramic Tile Adhesion

After the second waterproofing layer has dried for at least 24 hours, the installation of ceramic tiles can begin. The choice of adhesive depends on the dimensions and type of tiles, their water absorption, and the intended usage conditions. First, SiproFix BK 160 Super Flex, a flexible adhesive for ceramic and granite tiles for both interior and exterior use, is applied to the surface protected by the waterproofing coating. This adhesive can also be used for large-format tiles as well as in underfloor heating systems. The next step is the installation of ceramic tiles. Since they are installed using the contact adhesion method, at least 65% of the tile surface must be covered with adhesive. To ensure uniform spacing between tiles, we use plastic spacers.

Grouting and Sealing

Once the adhesive has completely dried, we proceed with grouting and sealing. BK-Fugomal is a high-quality, water-repellent grout for tile joints. It is intended for joints up to 10 mm wide and offers a choice of 24 shades. The grout is applied with a rubber trowel, diagonally to the joint lines (at a 45-degree angle). It is suitable for both indoor and outdoor use, on vertical and horizontal surfaces. In the final stage of installing the HYDRO CERAMIC BATHROOM system for waterproofing and laying ceramics, BK-Silicon Sanitar is applied. This sanitary silicone sealant is used for sealing joints between ceramic tiles in corners and where the wall meets the floor, as well as for sealing joints between sanitary ware and tiles in the bathroom. The silicone sealant is resistant to aging, shrinking, cracking, mold, UV radiation, and water exposure. Would you like to learn more? For additional information regarding waterproofing systems, installation methods, and pricing, you can contact the Bekament professional technical support team via email at [email protected]. We invite you to share your opinions on the advantages of high-quality bathroom waterproofing on our social media channels, Facebook / Instagram. Did you like the text? Share it with your friends.

What are the advantages of high-quality bathroom waterproofing?

When designing a modern home, a lot of attention is given to the bathroom, with the aim of equipping it in a contemporary way. The first step in creating a functional and aesthetically unique bathroom is installing bathroom waterproofing. The bathroom occupies about 10% of the home’s surface area, yet it is a space used daily for refreshing, making it one of the most sensitive areas in the home. If you’ve ever dealt with moisture and mold in the bathroom, you are aware of how much time is needed for remediation. Improper installation of bathroom waterproofing, or the lack thereof, can disrupt the aesthetic appearance of the space and negatively affect people’s health. To prevent potential issues caused by water and moisture, special attention should be paid to proper waterproofing installation. In the following blog, we will highlight the problems that inadequate bathroom waterproofing can cause. Additionally, we will discuss the benefits of well-chosen and properly installed waterproofing, as well as how to recognize and select it. Finally, we will present cement and acrylic waterproofing coatings as types of materials most commonly used and recommended by contractors daily.

Poor waterproofing affects both your health and household budget.

Whether it’s new bathroom construction or addressing waterproofing in an existing bathroom, improperly installed or poorly chosen waterproofing can cause additional difficulties and lead to lasting consequences. It can impact your health and result in extra costs. The appearance of mold and moisture on walls disrupts the look of the bathroom, making it uncomfortable to be in such a space. The air becomes heavy and gains an unpleasant odor, which negatively affects the mood and health of you and your family. Unhygienic and damp walls influence the occupant because daily exposure to unattractive spaces gradually fosters bad moods and negative feelings. The presence of moisture, mold, bacteria, and fungi on walls due to inadequate or damaged waterproofing affects both physical and mental health. The biggest issues arise when water from your bathroom finds a way to leak into a neighbor's apartment. In such cases, the situation becomes urgent, as subsequent waterproofing repairs require an immediate process that demands significant time and resources. Old tiles need to be demolished, and new ones must be installed in their place. Construction work can last for weeks, and you may also need to compensate the neighbor for damages. In other words, choosing and installing high-quality waterproofing in the bathroom and hiring professionals saves money and increases the value of your property. A space that is securely and long-term protected from water and moisture intrusion enhances the aesthetics and appearance of your bathroom.

Advantages of Quality Waterproofing

The purpose of bathroom waterproofing is to ensure a dry inter-floor structure, thereby providing favorable conditions for all rooms in the house or apartment, not just the bathroom or toilet. Due to its chemical composition, waterproofing prevents the passage of water and the penetration of moisture from the bathroom or toilet into other rooms. High-quality bathroom waterproofing primarily protects walls and ceilings from water damage. The key role of the waterproofing layer in the bathroom is to stop the penetration of water and moisture through the walls and ceiling.

Additionally, it prevents water from leaking through the floor and the appearance of cracks in the walls. It also stops the possibility of ceramic tiles coming loose and paint peeling off—common occurrences in damp and wet bathrooms. It is essential to hire professionals and experts who will correctly select and apply reliable waterproofing systems. Incorrectly chosen and applied waterproofing will cause further damage. Therefore, it is necessary to rely on best practices and expert advice.

Listen to Expert Advice

The majority of craftsmen, contractors, and tile setters in Serbia recommend and use polymer cement coatings for bathroom waterproofing. The advantage of this coating lies in its affordability and ease of application on curved surfaces, corners, and edges. Such areas would be much more difficult and expensive to properly waterproof with bitumen strips or other sealing materials. In other words, polymer cement coating is the best buy! Once dry, the polymer cement coating forms a durable waterproof membrane with a thickness of 2 to 3 mm. Water cannot seep through the floor, walls, or joints. The appearance of moisture or mold is prevented. It is a cost-effective and long-lasting solution due to its durability, wide applicability, and stability. There are several different cement-based waterproofing options on the domestic market, available in single-component or two-component packaging, based on Portland cement, polymer binders, and additives. Bekament products:

BK-HidroStop Base

BK-HidroStop 1

BK-HidroStop 2

BK-HidroStop 5/5

BK-HidroStop Extra

are waterproofing coatings for horizontal and vertical protection of surfaces against moisture, suitable for both exterior and interior use. Each is tailored to specific surfaces and varying user requirements based on its properties and functional characteristics. In addition to polymer cement waterproofing, the market also offers acrylic-based waterproofing. This is a liquid, ready-to-use waterproofing product. BK-HidroStop Premium is a flexible single-component waterproofing coating based on a polymer emulsion, designed for horizontal and vertical protection of interior surfaces from moisture before tiling, with a fine blue finish. It is suitable for use in systems with underfloor heating and is particularly useful for waterproofing gypsum board surfaces. The choice of waterproofing coating type depends on the position and the role the membrane needs to fulfill. However, in both cases, the proper installation of waterproofing is crucial. It is necessary to follow the manufacturer's recommendations and instructions.

Waterproofing That Lasts

Bathroom waterproofing is installed only once, but you will use your bathroom every day. That’s why its selection and installation deserve the utmost attention. Many contractors use polymer cement waterproofing coatings as the material that has proven to be the most effective in practice. Additionally, a large number of satisfied customers are the best guarantee that, with BEKAMENT products, your bathroom will also be permanently protected from flooding, leakage, and moisture. High-quality bathroom waterproofing provides secure and long-lasting protection from water and moisture intrusion, safeguards your health, and spares you from unexpected expenses. Check out our YouTube channel for the video “How to Properly Install a System for Waterproofing and Tiling in the Bathroom?”

For additional information regarding waterproofing systems, pricing, and installation methods, you can contact the Bekament professional technical support team via email at [email protected]. We invite you to share on our social media channels, Facebook / Instagram, your thoughts on the advantages of quality waterproofing. Enjoyed the article? Share it with your friends.

About interior paints

Colours, as well as smells, can have a profound effect on our mood and how we feel. They can evoke memories and evoke emotions. They can inspire and fill us with positive energy.
Adequate interior paint choices allow us to achieve striking results without major investment and complicated interventions. Colours can change the impression of the shape and size of a room, which gives us an additional opportunity in decorating the room. In modern rooms we use one basic colour or palette of related, mutually consistent colours. Emphases made in a different colour can be details on the wall surfaces themselves or pieces of furniture that give the room a sophisticated look.
No less important detail in the selection of colours is their environmental characteristics. Owing to state-of-the-art technological advancements, Bekament offers eco-friendly water-based interior paints that comply with the highest European standards. They are intended for a healthier life, free of toxic fumes and chemicals.
Personal affinities should certainly not be ruled out, but we must remember that the choice of interior colours is a serious and demanding process in which to take into account how our new environment will affect our productivity, mood and health. That is why it is very important that we take care and consult with experts when choosing the right colours for each place we live, whether we work, relax or have fun.

  Choice of interior colours is a serious and demanding process in which to take into account how our new environment will affect our productivity, mood and health.

  Red brings energy and speeds up the heart. The power of red is so great that even a small detail can have a strong effect. In the living room, it encourages conversation and good humour, and in the kitchen or dining room an appetite.

Thanks to the most up-to-date technological achievements, Bekament offers ecological water-based interior paints, in compliance with the highest European standards.

  Yellow, the colour of the sun encourages joy and happiness and brings warmth. Large areas of yellow can make the eyes tired, so it is best to use it for details or smaller surfaces. As a thought-provoking and intuitive colour, yellow or elements in this colour are good for work or study.
It is well known that green colour relaxes the eyes. What is perhaps less well known is that green encourages flexibility and creativity and inspires change and success.
If you want to bring an atmosphere of luxury to your home then purple is the right choice. In its darkest tones, purple is sophisticated and dramatic. It is tied to wealth and the perfect self for relaxation and relaxation rooms.
Health, warmth and the daily joy of life are infused with orange.
Bekament interior paints made on the basis of high quality raw materials, suitable for residential and commercial premises. They can be toned in a wide range of shades.
For a positive influence on moods, combine the colours that will make your home a healthy, happy, welcoming, creative and inspiring place to live, work, learn, socialize and relax.

Why is thermal insulation important?

Since ancient times, man has been constructing residential buildings made of different materials, primarily to protect against natural disasters. Over time, a man began to adjust the construction of buildings to his specific requirements, also in order to meet the need for comfort.  
In seeking for a solution while taking care of nature, Bekament has developed BEKATHERM facade systems that provide long-lasting and reliable protection of business and residential buildings from atmospheric influences, as well as the necessary comfort and warmth that turn a house into a home.
The thermal insulation system ( waterproofing )is one of the most important elements of every home because it protects it from weather influences, such as precipitation, wind, frost, heat and other environmental influences, and gives the desired aesthetic appearance. In the absence of thermal insulation, an average family home loses as much as 30% of the energy required for heating through the façade, and in residential buildings this percentage can be much higher. The role of the exterior wall as an element of the building envelope is to protect it from overheating, heat loss, atmospheric influences, as well as to have good accumulative capabilities to provide thermal and sound comfort within the building in order to reduce energy consumption. Energy efficiency is no longer a matter of personal choice. The legislation prescribes that each building must have an “energy passport”, a certificate of the energy performance of the building. Without this certificate, no newly constructed building will be able to obtain a exploitation permit. The main goal is to minimize energy consumption, while maintaining or even increasing the comfort level When it comes to buildings or homes that are energy efficient, we actually refer to buildings that entail higher energy savings in everyday life. Here, above all, we refer to maintaining a comfortable temperature, lighting and other conditions necessary for stay and work of people indoors. In a building that is thermally well insulated, the energy consumption for heating (in winter) and cooling (in summer) is noticeably smaller, and staying in it is more comfortable. An energy efficient building conserves energy, its life span is much longer, and one should not neglect the direct positive impact on conservation of the environment. No matter if new house or building is being built, or energy efficiency problems on an old single-family home or apartment building are being solved, the first step is to choose the right solution for the current project. When choosing materials, in addition to cost, it is necessary to take into account the quality and composition of used materials. BEKATHERM thermal insulation façade systems are of superior quality, which is confirmed by the results of control tests in authorized institutions both in Serbia and abroad, as well as the certificate for ETA standard (European Technical Assessment). Economical and proven, the BEKATHERM Standard with expanded polystyrene (EPS) panels provides lasting energy efficiency for buildings with energy savings of up to 40% and a guarantee of up to 25 years. In addition to the Standard system, Bekament also offers BEKATHERM Plus and BEKATHERM Prestige systems.

The BEKATHERM Standard with Expanded Polystyrene (EPS) boards provides lasting energy efficiency for buildings with energy savings of up to 40% and a guarantee of up to 25 years.